Fire-Lite ACC-25/50 Voice Evacuation Control Panel, Audio, Command. Though this information is based upon industry expertise and many years of experience, it is intend-ed to be used only as a guide. Voice Evacuation Panels that provide voice feedback depending on the state. It outlines basic principles that should be considered in the design of systems. Apply power to the panel.Fire and Security Prot., Fire Security Access C. about voice evacuation systems used in conjunction with fire alarm systems. If batteries are being used, connect the batteries (17 AH max.) to connector P2 located to the left center of the FC-PSM(E) Supply/Battery Charger Module. Complete the installation by connecting the AC power wires to the Hot, Neutral and Earth terminals of TB1 on the Power Supply/Battery Charger Module. Note that the Transformer cable connector is keyed to prevent connection. Plug the XRM-24(E) Transformer cable assembly into connector P1 which is located in the lower left corner of the Power Supply/Battery Charger Module. The ECC-50/100 and ECC-50/100E are multipurpose emergency voice evacuation panels that may be used for fire applications, mass notification. This connection is in order to provide proper lightning and transient protection for the panel. Connect a wire from a solid earth ground to one of the Transformer mounting studs and tighten the nut. Do not tighten one nut until the next step. Advanced solutions for fire, life safety.
Secure Transformer to the studs with the two supplied nuts. Resources for Wheelock notification appliances & SAFEPATH voice evacuation systems. Transformer should be oriented so the cable assembly is the left as illustrated below. Position XRM-24(E)Transformer Assembly over mounting studs. Transformer Installation Locate two threaded mounting studs in the bottom left corner of the backbox (refer to backbox illustration below).
FIRELITE VOICE EVAC INSTALL
2, 3 Standoff 1, 2, 3 factory jumper installing the Module 2, 3 Standoff 1, 2, 3 Standoff Power Supply/ Charger Module Evacuation Control Panel Circuit Board Remove two mounting screws from main board upper and lower left corners Main Circuit Board Install four metal standoffs by screwing place (note two different lengths) Install FC-PSM(E) Module and with four screws Circuit Main Circuit Board Backbox Mounting Rails Backbox Mounting Rails Backbox Mounting Rails Make certain all power (AC and DC) is removed before any connections are made. Continue with the FC-PSM(E) transformer installation as described on the following page. LiteSpeed and Lite-Connect are trademarks and Fire-Lite Alarms and SWIFT are registered. It is important that module be secured with the metal screws in order to help protect against lightning electrical transients. Voice messaging systems must be designed to meet intelligi. Secure the FC-PSM(E) to the standoffs using the two screws removed in Step 1 and two supplied screws. Make certain the pins are properly aligned to prevent bending or any pins. Carefully align connector J1 on the FC-PSM(E) Power Supply/Battery Charger Module with connector P7 on the main board and press the FC-PSM(E) securely into place. P7 is located on the bottom left corner the main circuit board (refer to illustration below). The mounting studs are located to the far left on each rail (refer to illustrations on following Remove the factory installed jumper from connector P7 of the main circuit board. Install the two supplied long metal standoffs by screwing them onto the threaded mounting studs in the top and bottom rails in the back box. Install two short metal standoffs, which are supplied with the FC-PSM(E) Power Supply/Battery Charger Module, by screw- them into the top left and bottom left corners of the main circuit board, where the screws were removed in Step 1. Power Supply/Battery Charger Module Installation Remove two mounting screws from the top left and bottom left corners of the main circuit board (largest circuit board closest to cabinet back). Evacuation Control Panel Power Supply/Battery Module Installation Drawing 50612 Rev B 8/8/97 ECN 97-303 Make certain all power (AC and DC) is removed before any connections are made.
In addition to supplying operating the modules are capable of charging 7 AH to 17 AH batteries.
FIRELITE VOICE EVAC FOR FREE
Through Potter Academy, you will be able to access hundreds of bite sized self-paced training modules, earn CEUs, and deepen your industry and product knowledge all for free Learn More Potter Announces Integrated Voice Systems. The FC-PSME requires VAC, 50 Hz, 0.5 amps. We are excited to introduce our new training hub, Potter Academy. Very easy to Program, I was amazed New Installation. Access MS Excel spreadsheets for calculating battery requirements for control panels, power supplies, and voice evacuation.
The FC-PSM(E) Power Supply/Battery Charger Module can be used to stand-alone power to the Voice Evacuation Control Panel. We dont usually install Fire-Lite, mostly EST, but it was the customers request. Fire-Lite tools include a variety of software, drawings and calculators to help you effectively plan and prepare for your next fire safety system installation.
0 kommentar(er)
